Winders Plastic Film

105″ PARKINSON HORIZ SURFACE WINDER

Stock #ZW60170

105″ PARKINSON HORIZ SURFACE WINDER

Stock #ZW60170

Used 105″ Parkinson Mark II horizontal surface winder for 2-ply, embossed, laminated tissue paper. Material thickness (dry): 0.5mm (nominal) material width range: 105″ max./80″ min. Material diameter range: 100″ max/36″ min material weight: 42.3 GSM (nominal) line speed range: 200...

Location: Mexico

Add to Cart View Details

15″ DAVIS STANDARD (2) POSITION WINDER

Stock #817-69

15″ DAVIS STANDARD (2) POSITION WINDER

Stock #817-69

Used 15″ wide Davis standard two-fixed position film/sheet winder for approximately 32″ diameter roll package. Includes air shafts, dancer, Penta DC variable SPPED control on each winding station. Includes slitter station with (2) slitters installed. Winder is caster mounted, S.O....

Location: Midwest USA

Add to Cart View Details

15″ KILLION SINGLE POS. WINDER

Stock #20613-18

15″ KILLION SINGLE POS. WINDER

Stock #20613-18

Used approximately 15″ wide Killion single position center winder, with 15″ wide X 3″ air shaft. Serial #13608. Includes motor.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

24″ SENCORP MDL LPW-20 PULL ROLL

Stock #ZP62258

24″ SENCORP MDL LPW-20 PULL ROLL

Stock #ZP62258

Used 24″ wide Sencorp Model LPW-20 winder, previously used for foam sheeting. Includes (2) rubber pull S-wrap pull rolls, and single winding shaft for 8″ cores. Includes operator control panel with DC volts and speed meters as well as tension...

Location: South USA

Add to Cart View Details

48″ WORLDWIDE 1990 42″ OD 2 POS TURRET

Stock #8315-2

48″ WORLDWIDE 1990 42″ OD 2 POS TURRET

Stock #8315-2

Used 48″ wide Worldwide 2-position turret winder, new 1990. Will accommodate 42″ diameter rolls, includes panel mate, Modicon control system for operator control, has Reliance max pack drive control panel and (2) 15 HP DC motors with transformers, has hydraulic...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

54″ GEC MDL 126 18″ OD SHAFTLESS 1974

Stock #8429-8

54″ GEC MDL 126 18″ OD SHAFTLESS 1974

Stock #8429-8

Used 54″ wide Gloucester model 126 single turret winder, serial number 18009-01. New 1974. Shaftless design, will accommodate 18″ diameter rolls. Both winding stations are driven by a single DC motor with control. Includes dancer for speed control.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

54″ JOHNSON SINGLE TURRET 24″ OD

Stock #8794-1W

54″ JOHNSON SINGLE TURRET 24″ OD

Stock #8794-1W

Used Johnson 54″ single turret winder able to handle up to 24″ diameter packages. Unit has 6″ air shafts, Layon roll, and dancer. Power requirements 460/3/60, 14 amps.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

64″ Gloucester Model 124 Shaftless Dual Turret Winder

Stock #20112-39

64″ Gloucester Model 124 Shaftless Dual Turret Winder

Stock #20112-39

Used 64″ wide Gloucester model 124 dual turret winder. Serial #16101-24. New 1972. Will accommodate maximum 24″ diameter rolls, shaftless design. Has 67″ wide secondary nip station, with each turret equipped with a 3/4HP 230/460 volt AC motor for turret...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

80″ ASHE SINGLE TURRET WITH FLY KN AUTO UNLOAD

Stock #20490-3

80″ ASHE SINGLE TURRET WITH FLY KN AUTO UNLOAD

Stock #20490-3

Used 80″ wide Ashe single turret winder, with differential shaft, with flying knife assembly and auto unloading. Serial #695-09. Each winding position is capable of max. 12″OD rolls and is equipped with .55 kW AC motor with variable frequency controller....

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

84″ MAIER (2) SHAFT WINDERS

Stock #20582-1W

84″ MAIER (2) SHAFT WINDERS

Stock #20582-1W

Used 84″ wide Maier hydraulically powered fixed, single shaft winders mounted on portable carts. Package includes the following: (2) hydraulic power packs with hydraulic motors, model WKN24M3-2, serial #3057, 3058. 460 volt AC input (1) for each side of winder...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90″ ASHE “SAPPHIRE SERIES” DUAL TURRET APPRX 20

Stock #ZP62207

90″ ASHE “SAPPHIRE SERIES” DUAL TURRET APPRX 20

Stock #ZP62207

Used 90″ Ashe dual turret winder, manufactured approximately 2011. Includes Ashe Sapphire series accumulator with maximum web width of 102″. Has Sapphire slitting with (2) trim winders, Ashe dual turret winding station and Ashe dual position turret style unloading station...

Location: South USA

Add to Cart View Details

96″ AFEX 2-POSITION SURFACE W/NIP 40″ OD

Stock #20814-17

96″ AFEX 2-POSITION SURFACE W/NIP 40″ OD

Stock #20814-17

Used 96″ wide Apex 2-position Surface Winder, Model 21220, including a secondary nip roll assembly with slitting station. Will accomodate maximum 40″ O.D. Roll, includes operator control panel and (2) pendant controls for operator input. Winder is equipped with (10)...

Location: Perry New Jersey Warehouse

Add to Cart View Details

96″ EGAN SINGLE TURRET DOUBLE DIRECTION WINDER

Stock #M3137J-001

96″ EGAN SINGLE TURRET DOUBLE DIRECTION WINDER

Stock #M3137J-001

Used 96″ Egan single turret double direction winder able to handle up to 36″ diameter packages on either 3″ or 6″ air shafts. Unit was designed to run a 92″ wide web, 4.5 to 45 mils thick at speeds from...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details