3 1/2" Extruders

3″ Hydreclaim Reprocessing Extruder

Stock #20175-515EXT

3″ Hydreclaim Reprocessing Extruder

Stock #20175-515EXT

Used approximately 3″ diameter Hydreclaim side fed film reprocessing extruder, previously used with Gala pelletizer and force feed fluff bin.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3″ Graham Engineering Corp. Single Screw Extruder L/D 24:1 Non-Vented

Stock #776-82C

3″ Graham Engineering Corp. Single Screw Extruder L/D 24:1 Non-Vented

Stock #776-82C

Used 3″ 24/1 L/D Graham Engineering Corporation single screw extruder. Model 3024-a, serial #45762-89. Has electrically heated non-vented and air cooled 4-zone barrel with a 20″ centerline height. Feed throat is water cooled, no hopper included. Driven by a 60...

Location: Midwest USA

Add to Cart View Details

3.00 Davis Standard Extruder 30/1 L/D

Stock #820-213

3.00 Davis Standard Extruder 30/1 L/D

Stock #820-213

Used 3″ Davis Standard Mark V extruder. 30/1 L/D non vented barrel, electrically heated and air cooled. Extruder previously mounted on auxiliary base supplying approximately 97″ center line height available with the extruder if requested. Now removed from the auxiliary...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3 1/2″ Royle Plastic Extruder L/D 16:1

Stock #2826-4

3 1/2″ Royle Plastic Extruder L/D 16:1

Stock #2826-4

Used 3 1/2″ Royle 16/1 L/D plastic extruder. Serial #2663. Electric Spirod heaters with air and water cooling. Has 4 zone temperature control panel. Fitted with 5/8″ X 7/8″ head. Right angle reducer to 60 HP Louis Allis type CLC...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3.5″ American Kuhne Extruder

Stock #20844-64

3.5″ American Kuhne Extruder

Stock #20844-64

Used 3.5″ 24/1 L/D American Kuhne single screw extruder, non vented, air cooled barrel with 30″ barrel center line height. Model # AK 350, Serial # 1957. New in 2000. Driven by a 75 HP, 1780rpm, AC motor with variable...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3.5″ NRM Extruder L/D 24:1 Air-Cooled

Stock #ZP61230-2

3.5″ NRM Extruder L/D 24:1 Air-Cooled

Stock #ZP61230-2

Used 3.5″ 24/1 L/D NRM Pacemaker iv air cooled extruder. New 1995. Driven by 75 HP Reliance motor with Reliance VS power module drive. Has 15.12/1 gearbox ratio. Unit presently 36″ centerline height. Includes temperature control panel with solid state...

Location: Midwest USA

Add to Cart View Details

3.5″ PTI Extruder Trident Series Model 3500 28:1

Stock #638-610-04

3.5″ PTI Extruder Trident Series Model 3500 28:1

Stock #638-610-04

Used PTI model 3500 trident series 3-1/2″ 28/1 extruder having a 4-zone electrically heated, air cooled barrel at approximately a 94″ centerline height. Gearbox is a Flenders model SZNF270, has a reduction ratio of 22.18:1 with a service rating of...

Location: Midwest USA

Add to Cart View Details

3.5″ Sterling Hi-Boy Extruder L/D 30:1

Stock #ZP57793

3.5″ Sterling Hi-Boy Extruder L/D 30:1

Stock #ZP57793

Used 3.5″ Sterling 30/1 L/D HI-Boy extruder. Has 72″ centerline height, new 1983. Includes PVC screw, driven by 75 HP DC motor with SCR control. Has gearbox with 14/1 reduction, has electrically heated barrel with cast aluminum water cooled heaters....

Location: Midwest USA

Add to Cart View Details

3.5″ Welex Extruder 30:1

Stock #M4205J

3.5″ Welex Extruder 30:1

Stock #M4205J

Used 3.5″ 30:1 Welex extruder having an electrically heated, air cooled barrel. Lufkin change 7.76 to 1 gear ratio gearbox was originally driven by a 100 HP DC motor which is missing. With integral temperature panel with Barber Coleman 580...

Location: Midwest USA

Add to Cart View Details

3.5″ Davis Standard Lowboy Extruder L/D 30:1 Non-Vented

Stock #20603-79

3.5″ Davis Standard Lowboy Extruder L/D 30:1 Non-Vented

Stock #20603-79

Used 3.5″ Davis Standard Thermatic III 30/1 L/D non-vented, lowboy extruder. Has electrically heated air cooled barrel, “lowboy” barrel height with 25″ centerline. Extruder includes hopper, heat panel but requires temperature controllers, and Allen Bradley inverter for AC drive, 460...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3-1/2″ Davis Standard Extruder 30:1 Vented

Stock #ZP50749

3-1/2″ Davis Standard Extruder 30:1 Vented

Stock #ZP50749

Used 3-1/2″ 30/1 Davis standard extruder having a 5 zone electrically heated water cooled, vented and plugged barrel at a 72″ centerline height. Gearbox has a ratio of 11.8:1, is rated at 158 HP with a service factor of 1.25....

Location: Midwest USA

Add to Cart View Details

3.5″ Welex Extruder L/D 30:1 Vented

Stock #9547-1

3.5″ Welex Extruder L/D 30:1 Vented

Stock #9547-1

Used 3.5″ Welex 30/1 L/D extruder. New 1984, serial #2453. Has electrically heated, water cooled (closed loop), vented, and plugged barrel. Includes vent stack and vacuum pump. Includes Koellmann gearbox with 11.26/1 ratio, SN# 2270773, size UNEX 5.0, rated at...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3.5″ Alfa Marathon Single-Screw Extruder 30:1 Vented

Stock #20031-1

3.5″ Alfa Marathon Single-Screw Extruder 30:1 Vented

Stock #20031-1

Used 3.5″ 30/1 Alfa Marathon single-screw extruder. Unit has an electrically heated, water cooled, and vented barrel. 30″ centerline height. Gearbox has reduction ratio of 11.2:1 and is driven by 150 HP, 575 volt, 60 HZ, 1750 RPM AC motor...

Location: Midwest USA

Add to Cart View Details

3.5″ CDL 32/1 L/D Dual Diameter Crown Reclaim Extruder

Stock #20932-1

3.5″ CDL 32/1 L/D Dual Diameter Crown Reclaim Extruder

Stock #20932-1

Used approximately 3.5/4.5 dual diameter Crown reclaim extruder, designed for low bolt density material. Has 8″ x 16″ water cooled feed throat with air actuated stuffer ram. Extruder has 32/1 L/D vented barrel, electrically heated water cooled. Includes 75 hp...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

3.5″ Polytruder Extruder 34/1 L/D Non-Vented

Stock #ZP62223

3.5″ Polytruder Extruder 34/1 L/D Non-Vented

Stock #ZP62223

Used 3.5″ Polytruder 34/1 L/D non-vented extruder. Electrically heated air cooled barrel, driven by 125 HP DC motor with SCR control, 480 volt AC input. Has transformer base mounted, Flender gear reducer with 17.6:1 gear ratio, single stage feed screw...

Location: South USA

Add to Cart View Details

90mm Barmag Extruder L/D 30:1 Non-Vented

Stock #626-08

90mm Barmag Extruder L/D 30:1 Non-Vented

Stock #626-08

Used 90mm Barmag 30/1 L/D, non-vented extruder. Barrel centerline height 39″, electrically heated but does not have any cooling on the barrel; has provisions to be added. Extruder is type 9E10/30D, serial # 12/2407-1. Gearbox model 9E805-32/6V. Has water cooled...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90mm Barmag Extruder L/D 30:1 Non-Vented

Stock #626-05

90mm Barmag Extruder L/D 30:1 Non-Vented

Stock #626-05

Used 90mm Barmag 30/1 L/D non-vented extruder. Barrel centerline height 39″, electrically heated but does not have any cooling on the barrel; has provisions to be added. Extruder is type 9E10/30D, serial: 12/2407-4. Gearbox model 9E805-32/6V. Has water cooled top...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-13

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-13

Used 90mm Barmag 30/1 L/D non-vented extruder. Barrel centerline height 39″, electrically heated but does not have any cooling on the barrel; has provisions to be added. Extruder is type 9E10/30D, serial #12/2225. Gearbox model 9E805-32/6V. Has water cooled top...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-10

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-10

Used 90mm Barmag 30/1 L/D, non-vented extruder barrel centerline height 39″, electrically heated air cooled barrel. Extruder is type 9E10/30D, serial #12/2407-3. Gearbox model 9E805-32/6V. Has water cooled top center feed throat 4.5″ X 6″. Includes stainless steel hopper approximately...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-09

90mm Barmag Extruder L/D Non-Vented 30:1

Stock #626-09

Used 90mm Barmag 30/1 L/D non-vented extruder. Barrel centerline height 39″, electrically heated but does not have any cooling on the barrel; has provisions to be added. Extruder is type 9E10/30D, serial #9008928-1. Gearbox model 9E805-32/6V. Has water cooled top...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

90mm Union Extrusion Spa. Single-Screw Extruder L/D 44:1 Non-Vented

Stock #ZP61648

90mm Union Extrusion Spa. Single-Screw Extruder L/D 44:1 Non-Vented

Stock #ZP61648

Used 90mm Union extrusion spa. Single screw extruder. Has 44/1 L/D non-vented barrel, electrically heated and 5 zones with air cooling, and 4 zones with water cooling. Includes temperature control panel. Includes 50HP motor but no drive. Includes screw for...

Location: N/A

Add to Cart View Details

3.75″ Berstorff Extruder L/D 17:1

Stock #ZP49072

3.75″ Berstorff Extruder L/D 17:1

Stock #ZP49072

Used 3.75 O.D. Berstorff model EG4/480 side feed cross head extruder. 17/1 L/D, electrically heated barrel with water cooling utilizing cast aluminum heaters. Has Rotary Union for screw. Gearbox rated at 56 kW but no motor included. 1982. Serial number...

Location: South USA

Add to Cart View Details

100mm Davis Standard Single Screw Extruder 26:1

Stock #9538-350

100mm Davis Standard Single Screw Extruder 26:1

Stock #9538-350

Used 100mm 26/1 Davis standard model 3.5MV-350 single screw extruder. New 12/2000. Serial #16467. Driven by 60 HP AC motor 3/60/460V with AC variable speed inverter. Has electrically heated 5- zoned air cooled barrel. Includes temperature control panel with 5...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

100mm Davis Standard Extruder L/D 30:1 Non-Vented

Stock #9540-4

100mm Davis Standard Extruder L/D 30:1 Non-Vented

Stock #9540-4

Used 100mm Davis standard 30/1 L/D non-vented barrel, electrically heated, water cooled. Model 100mm35F, serial #M3027. No temperature control panel. Gearbox ratio is 17.44/1, new 12/91. Extruder is belt driven to 125 HP Reliance DC with Reliance SCR control.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details