2 1/2" Extruders

2″ Akron Extruder L/D 24:1 3-Zone Electrically Heated Air Cooled

Stock #9851-05

2″ Akron Extruder L/D 24:1 3-Zone Electrically Heated Air Cooled

Stock #9851-05

Used 2″ 24/1 Akron model PAC 200 extruder having a three zone electrically heated, air cooled at a 42″ centerline height. Gearbox is a Koellmann model PEZS230, has a reduction ratio of 13.92/1 and is rated at 35 HP at...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2″ HPM Extruder L/D 24:1 Single Screw

Stock #20263-08

2″ HPM Extruder L/D 24:1 Single Screw

Stock #20263-08

Used 2″ HPM 24/1 L/D single screw extruder, model 2.0 TMC-24. Electrically heated, air cooled, 3-zone, non-vented barrel. Water cooled feed throat with hopper. Approximately 29-1/2″ centerline height. Driven by a 20 HP 500 volt, 2500 rpm DC motor through...

Location: Midwest USA

Add to Cart View Details

2″ Deltaplast Cold Feed Extruder L/D 24:1 Air-Cooled

Stock #20389-21

2″ Deltaplast Cold Feed Extruder L/D 24:1 Air-Cooled

Stock #20389-21

Used 2″ Deltaplast cold feed extruder, 24:1 L/D, electrically heated, air cooled barrel, jacketed feed section, pedestal mounted with power roll strip feeder driven by a 1/4 HP DC motor. Extruder driven by 25 HP DC main drive, with control...

Location: Midwest USA

Add to Cart View Details

2″ Davis Standard Extruder 24/1 L/D Non-Vented Air Cooled

Stock #20890-2

2″ Davis Standard Extruder 24/1 L/D Non-Vented Air Cooled

Stock #20890-2

Used 2″ Davis Standard Model DS20 24/1 L/D air cooled non-vented extruder. Extruder is driven by a 40 hp DC motor with Reliance SCR controller. Has base mounted temperature control panel, 17.5/1 gear ratio, water cooled top center feed. Serial...

Location: Perry New Jersey Warehouse

Add to Cart View Details

60mm Berstorff Single Screw Extruder 28:1 Air-Cooled

Stock #ZP60152

60mm Berstorff Single Screw Extruder 28:1 Air-Cooled

Stock #ZP60152

Used 60mm 28/1 Berstorff single screw extruder having three electrically heated, air cooled barrel zones and two oil heated zones, at a 42″ centerline height. Gearbox has a ratio of 11.2 and is driven by a 25 HP DC motor....

Location: Midwest USA

Add to Cart View Details

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #ZP61791

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #ZP61791

Used 2.5″ Davis standard Thermatic 24/1 L/D non-vented extruder. New 1994. Extruder is equipped with 100 rpm screw speed, temperature control panel with instruments, stainless steel hopper, electrically heated air cooled barrel, and belt driven to 40 HP DC motor...

Location: SOUTH USA

Add to Cart View Details

2.5″ NRM Pacemaker III Extruder L/D 24:1 4-Zone

Stock #8492-EXT

2.5″ NRM Pacemaker III Extruder L/D 24:1 4-Zone

Stock #8492-EXT

Used 2.5″ NRM 24/1 L/D Pacemaker III extruder having a four zone electrically heated, air cooled, barrel at a 42″ centerline height. Extruder is presently mounted on a steel base allowing for approximately a 70″ centerline height. Gearbox has a...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Welex Extruder L/D 24:1 Non-Vented

Stock #9547-3

2.5″ Welex Extruder L/D 24:1 Non-Vented

Stock #9547-3

Used 2.5″ Welex model 250-24/1-RHNV 24/1 L/D non-vented extruder. Has electrically heated and air cooled barrel. Includes manual screen changer and melt pump with motor. Gearbox ratio 9.3/1, rated at 110 HP, service factor 1.0, input rpm 1750, output rpm...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #9540-5

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #9540-5

Used 2.5″ Davis Standard Model 25IN25 with 24/1 L/D non-vented barrel, electrically heated, water cooled but no water system included. No temperature control panel. Driven by a 50 HP Reliance DC motor with SCR control.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Battenfeld Gloucester Extruder L/D 30:1 Air-Cooled

Stock #20331-6

2.5″ Battenfeld Gloucester Extruder L/D 30:1 Air-Cooled

Stock #20331-6

Used 2.5″ Battenfeld Gloucester extruder, 30:1 L/D, electrically heated, air cooled with Contracool, jacketed feed section, 60 HP DC motor with SCR controller, manual screen changer, 69.5″ center line height currently can be lowered to 49.5″ center line height, 13.75:1...

Location: Midwest USA

Add to Cart View Details

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-82A

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-82A

Used 2.5″ 24/1 L/D Graham Engineering Corporation single screw extruder. Model 2524, serial #46502-90. Electrically heated and air cooled 4-zone barrel with a 42″ centerline height. Has jacketed infeed section. No hopper included. Driven by a 60 HP, 500 volt,...

Location: Midwest USA

Add to Cart View Details

2.5″ Egan Extruder L/D 28:1 Non-Vented

Stock #20209-4

2.5″ Egan Extruder L/D 28:1 Non-Vented

Stock #20209-4

Used 2.5″ Egan 28/1 L/D non vented extruder. Serial #F004347-01. Has electrically heated, water cooled barrel. Includes material hopper, barrel mounted temperature control panel with 7 Barber Coleman 520 instruments. Driven by 50 HP DC motor, 500 volts, 1750/2100 rpm....

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Gloucester Extruder L/D 30:1 Non-Vented

Stock #6176-EX

2.5″ Gloucester Extruder L/D 30:1 Non-Vented

Stock #6176-EX

Used 2.5″ Gloucester 30/1 L/D non-vented extruder. Standard height extruder with 42″ center line. Driven by 40 HP DC motor with mentor II digital control (added 1993). Extruder is jacketed for heating or cooling in the first two zones, electrically...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Davis Standard Extruder L/D 30:1 Non-Vented

Stock #20603-120

2.5″ Davis Standard Extruder L/D 30:1 Non-Vented

Stock #20603-120

Used 2.5″ Davis Standard Thermatic 30/1 L/D non-vented extruder. New 2005. Recently tested and in running condition. Extruder is belt driven to 50 HP AC motor with inverter. Includes Davis standard gearbox model 25in25, with 17.26/1 gear ratio rated at...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Welex Extruder L/D 30:1 Non-Vented

Stock #ZP55546

2.5″ Welex Extruder L/D 30:1 Non-Vented

Stock #ZP55546

Used Welex 2.5″ 30:1 L/D extruder, model 250-30:1RHNV. New 1978. Has electrically heated, air cooled, non-vented barrel. Driven by a 50 HP DC motor with spectrum drive, Lufkin gearbox 17.71:1, rated at 88 HP, output rpm 99. Includes temperature control...

Location: Midwest USA

Add to Cart View Details

2.5″ Brampton Engineering Extruder L/D 30:1 Non-Vented

Stock #773-473A

2.5″ Brampton Engineering Extruder L/D 30:1 Non-Vented

Stock #773-473A

Used 2.5″ Brampton Engineering 30/1 L/D extruder model #mod250-30:1ace, serial #12772-2. Has electrically heated air cooled non-vented barrel, includes XALOY/Dynisco manual screen changer, temperature control panel with 14 instruments. Extruder is belt driven by a 60 HP DC motor with...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.25″ Gloucester Extruder 30:1 Air-Cooled

Stock #9545

2.25″ Gloucester Extruder 30:1 Air-Cooled

Stock #9545

Used 2.5″ Gloucester model 25225R-2 extruder. Has electrically heated, air cooled barrel. Set up for contra cool, but does not include blower. Gearbox has a ratio of 9.6:1 and is direct driven by 60 HP DC motor with SCR. No...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ American Kuhne 30/1 L/D Loboy Extruder

Stock #20844-55

2.5″ American Kuhne 30/1 L/D Loboy Extruder

Stock #20844-55

Used 2.5″ American Kuhne, 1999, 30/1 L/D loboy extruder, model AK250-AC ext, serial #1954, including the following: Koellmann gearbox, belt driven to 125 HP AC motor with variable frequency drive, 460 volt AC input gearbox rated at 14/1 ratio, 150HP,...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Welex Extruder L/D 30:1Vented

Stock #9547-2

2.5″ Welex Extruder L/D 30:1Vented

Stock #9547-2

Used 2.5″ Welex model 250-30/1-RHSV 30/1 L/D extruder. Has electrically heated, air cooled, vented, and plugged barrel. Includes manual screen changer and melt pump. Gearbox driven by 50 HP DC motor with SCR control. Includes temperature control panel. Serial #2064....

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ PTI Extruder L/D 32:1 5-Zone Electrically Heated

Stock #638-610-06

2.5″ PTI Extruder L/D 32:1 5-Zone Electrically Heated

Stock #638-610-06

Used PTI model 2500 trident 2-1/2″ 32:1 extruder having a 5-zone electrically heated air cooled barrel at approximately 89″ centerline height. Unit has a Coleman model UNEX 4.1 gearbox having a 17.533:1 reduction ratio, has a service rating of 75...

Location: Midwest USA

Add to Cart View Details

60mm Reifenhauser Single Screw Extruder L/D 32:1

Stock #ZP60562

60mm Reifenhauser Single Screw Extruder L/D 32:1

Stock #ZP60562

Used 60mm Reifenhauser model eh350-1-60-60 32/1 L/D single screw extruder. Driven by 40 kW motor. Previously used at 80 kilograms per hour on polyethylene and polypropylene. Has vented barrel, candle type filter, and water cooling system. Separately available is a...

Location: UN

Add to Cart View Details