2 1/2" Extruders

2″ Davis Standard Extruder 24:1 L/D Non-Vented Air Cooled

Stock #20890-2

2″ Davis Standard Extruder 24:1 L/D Non-Vented Air Cooled

Stock #20890-2

Used 2″ Davis Standard Model DS20 24/:1 L/D air cooled non-vented extruder. Extruder is driven by a 40 hp DC motor with Reliance SCR controller. Has base mounted temperature control panel, 17.5:1 gear ratio, water cooled top center feed. Serial...

Location: Perry New Jersey Warehouse

Add to Cart View Details

2″ Hartig Extruder 30/1 L/D With Spare Screws

Stock #21058-02

2″ Hartig Extruder 30/1 L/D With Spare Screws

Stock #21058-02

Used 2″ Hartig extruder with approximately 30/1 L/D. Includes temperature control panel, DC motor and SCR control. Includes 6 spare screws. Electrically heated and water cooled vented/plugged barrel.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2″ PTI Single Screw Extruder 24/1 L/D

Stock #21099-03

2″ PTI Single Screw Extruder 24/1 L/D

Stock #21099-03

Used 2″ 24/1 L/D PTI single screw Extruder. Model 2000, Serial #2565EXT, new 1998. Has electrically heated water cooled barrel, includes pump, heat exchanger and water reservoir. Belt driven by 25 hp AC motor, 460 volt AC input, with variable...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2″ Prodex Single Screw Extruder 24/1 L/D

Stock #21099-06

2″ Prodex Single Screw Extruder 24/1 L/D

Stock #21099-06

Used 2″ Prodex 24/1 L/D single screw extruder. Driven by 15 hp DC motor, includes temperature control panel, SCR controller and individual instruments for each zone. With electrically heated and water cooled barrel. Includes 2-component hopper (agitation in primary hopper),...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2″ Akron Extruder L/D 24:1 3-Zone Electrically Heated Air Cooled

Stock #9851-05

2″ Akron Extruder L/D 24:1 3-Zone Electrically Heated Air Cooled

Stock #9851-05

Used 2″ 24:1 Akron model PAC 200 extruder having a three zone electrically heated, air cooled at a 42″ centerline height. Gearbox is a Koellmann model PEZS230, has a reduction ratio of 13.92:1 and is rated at 35 HP at...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

60mm Berstorff Single Screw Extruder 28:1 Air-Cooled

Stock #ZP60152

60mm Berstorff Single Screw Extruder 28:1 Air-Cooled

Stock #ZP60152

Used 60mm 28:1 Berstorff single screw extruder having three electrically heated, air cooled barrel zones and two oil heated zones, at a 42″ centerline height. Gearbox has a ratio of 11.2 and is driven by a 25 HP DC motor....

Location: Midwest USA

Add to Cart View Details

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #9540-5

2.5″ Davis Standard Extruder L/D 24:1 Non-Vented

Stock #9540-5

Used 2.5″ Davis Standard Model 25IN25 with 24:1 L/D non-vented barrel, electrically heated, water cooled but no water system included. No temperature control panel. Driven by a 50 HP Reliance DC motor with SCR control.

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Brampton Engineering Extruder L/D 30:1 Non-Vented

Stock #773-473A

2.5″ Brampton Engineering Extruder L/D 30:1 Non-Vented

Stock #773-473A

Used 2.5″ Brampton Engineering 30:1 L/D extruder model #MOD250-30:1ACE, serial #12772-2. Has electrically heated air cooled non-vented barrel, includes XALOY/Dynisco manual screen changer, temperature control panel with 14 instruments. Extruder is belt driven by a 60 HP DC motor with...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Davis Standard Mark V Non-Vented Extruder 24/1 L/D

Stock #21079-6

2.5″ Davis Standard Mark V Non-Vented Extruder 24/1 L/D

Stock #21079-6

Used 2.5″ Davis Standard Mark V 24/1 L/D non-vented Extruder. Model 2.5IN25MK5, Serial #R3630. New 1995. Has electrically heated air cooled barrel. Driven by a 40 hp AC motor with variable frequency drive, 460 volt, 60 hz. Has 17.2 gear...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Killion Extruder 24:1 L/D Non-Vented Air Cooled

Stock #ZP62585

2.5″ Killion Extruder 24:1 L/D Non-Vented Air Cooled

Stock #ZP62585

Used 2.5″ 24/1 L/D Killion non-vented Extruder. Has electrically heated, air cooled barrel. Driven by a 40 HP DC motor with SCR controller. Gearbox ratio 9.3:1. Includes temperature control panel. 240 volt.

Location: Midwest USA

Add to Cart View Details

2.5″ NRM Pacemaker III Extruder L/D 24:1 4-Zone

Stock #8492-EXT

2.5″ NRM Pacemaker III Extruder L/D 24:1 4-Zone

Stock #8492-EXT

Used 2.5″ NRM 24:1 L/D Pacemaker III extruder having a four-zone electrically heated, air cooled, barrel at a 42″ centerline height. Extruder is presently mounted on a steel base allowing for approximately a 70″ centerline height. Gearbox has a reduction...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-62B

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-62B

Used 2.5″ 24:1 L/D Graham Engineering Corporation single screw extruder. Model 2524, serial #46462-91. Electrically heated and air cooled 4-zone barrel with a 42″ centerline height. Has water cooled feedthroat, no hopper included. Driven by a 60 HP 500 volt...

Location: Midwest USA

Add to Cart View Details

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-82A

2.5″ Graham Engineering Corp. Single Screw Extruder L/D 24:1

Stock #776-82A

Used 2.5″ 24:1 L/D Graham Engineering Corporation single screw extruder. Model 2524, serial #46502-90. Electrically heated and air cooled 4-zone barrel with a 42″ centerline height. Has jacketed infeed section. No hopper included. Driven by a 60 HP, 500 volt,...

Location: Midwest USA

Add to Cart View Details

2.5″ Egan Extruder L/D 28:1 Non-Vented

Stock #20209-4

2.5″ Egan Extruder L/D 28:1 Non-Vented

Stock #20209-4

Used 2.5″ Egan 28:1 L/D non vented extruder. Serial #F004347-01. Has electrically heated, water cooled barrel. Includes material hopper, barrel mounted temperature control panel with 7 Barber Coleman 520 instruments. Driven by 50 HP DC motor, 500 volts, 1750/2100 rpm....

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.25″ Gloucester Extruder 30:1 Air-Cooled

Stock #9545

2.25″ Gloucester Extruder 30:1 Air-Cooled

Stock #9545

Used 2.5″ Gloucester model 25225R-2 extruder. Has electrically heated, air cooled barrel. Set up for contra cool, but does not include blower. Gearbox has a ratio of 9.6:1 and is direct driven by 60 HP DC motor with SCR. No...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ American Kuhne 30:1 L/D Loboy Extruder

Stock #20844-55

2.5″ American Kuhne 30:1 L/D Loboy Extruder

Stock #20844-55

Used 2.5″ American Kuhne, 1999, 30:1 L/D loboy extruder, model AK250-AC ext, serial #1954, including the following: Koellmann gearbox, belt driven to 125 HP AC motor with variable frequency drive, 460 volt AC input gearbox rated at 14:1 ratio, 150HP,...

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

2.5″ Welex Extruder L/D 30:1 Vented

Stock #9547-2

2.5″ Welex Extruder L/D 30:1 Vented

Stock #9547-2

Used 2.5″ Welex model 250-30/1-RHSV 30:1 L/D extruder. Has electrically heated, air cooled, vented, and plugged barrel. Includes manual screen changer and melt pump. Gearbox driven by 50 HP DC motor with SCR control. Includes temperature control panel. Serial #2064....

Location: On Site at Perry (Hainesport, NJ - USA)

Add to Cart View Details

60mm Reifenhauser Single Screw Extruder L/D 32:1

Stock #ZP60562

60mm Reifenhauser Single Screw Extruder L/D 32:1

Stock #ZP60562

Used 60mm Reifenhauser model EH350-1-60-60 32:1 L/D single screw extruder. New 1971. Driven by 40 kW motor. Previously used at 80 kilograms per hour on polyethylene and polypropylene. Has vented barrel, candle type filter, and water cooling system. Separately available...

Location: UN

Add to Cart View Details